Ultrasonic cleaning is widely used for removing machining oil, metal chips and fine particles from CNC-machined components. However, when cleaning parts with blind holes, threaded holes and internal channels, achieving consistent results can be more challenging than cleaning flat external surfaces.
A common problem in industrial cleaning is that a component looks clean on the outside, but small amounts of machining residue remain inside its internal passages.
This is particularly important for hydraulic valve blocks, aluminium manifolds, precision housings and automotive components, where residual particles may affect subsequent assembly or equipment performance.
Understanding why these residues remain is essential for developing a reliable ultrasonic cleaning process.
1. The Hidden Problem: Trapped Air Inside Blind Holes
A blind hole is a hole that does not pass completely through a component. Unlike a through-hole, it has only one opening, making it more difficult for cleaning liquid to enter and drain.
When a component is immersed in an ultrasonic cleaning tank, air can become trapped inside these holes.
This creates a problem because ultrasonic cavitation occurs in the cleaning liquid. If a cavity remains filled with air, the liquid cannot fully contact its internal surface, meaning the ultrasonic cleaning action cannot work effectively in that area.
For example, consider an aluminium hydraulic valve block with several drilled oil passages. Its external surfaces may become clean relatively quickly, while some internal holes continue to hold machining coolant, fine chips or air pockets.
The important point: Ultrasonic power alone cannot solve a problem caused by trapped air. The cleaning liquid must first reach the contaminated surface.
2. Why Component Positioning Matters More Than Expected
One of the most overlooked factors in ultrasonic cleaning is how components are placed inside the cleaning basket.
Simply placing parts randomly into a basket may work for simple components, but it is not always suitable for parts with complex internal structures.
Here are three practical considerations:
A. Allow trapped air to escape
Blind holes should be positioned so that air can escape as the component is submerged. Depending on the geometry, an angled or sideways position may help the liquid enter more effectively.
B. Avoid overlapping components
When parts are stacked or placed too closely together, some surfaces may be shielded from the active cleaning liquid.
For precision components, using a suitable fixture or arranging parts in a single layer can improve cleaning consistency.
C. Consider both filling and draining
A hole that fills with cleaning liquid during immersion must also be able to drain during removal. The correct orientation should therefore be evaluated throughout the entire cleaning and rinsing process.
For complicated components with multiple internal passages, changing the component orientation during cleaning may be necessary.
3. The Role of Degassing in Cleaning Performance
Freshly prepared cleaning liquid contains dissolved gases. Excessive dissolved gas can reduce the intensity of cavitation because gas inside the bubbles cushions their collapse.
This is why degassing is an important preparation step, especially when a cleaning tank is filled with fresh liquid.
A practical preparation process includes:
Fill the tank with the recommended cleaning solution.
Adjust the liquid temperature according to the detergent manufacturer's instructions.
Activate the ultrasonic function or dedicated Degas mode.
Allow sufficient time for dissolved gases to escape before loading precision components.
Some ultrasonic cleaners include a dedicated Degas function to simplify this process.
It is worth remembering that degassing the tank liquid and removing air trapped inside a component's blind holes are related but different challenges. Both need to be considered.
4. Selecting the Right Cleaning Parameters for Different Components
Not every CNC-machined component requires the same ultrasonic cleaning conditions.
The correct combination of frequency, power, temperature, and cleaning time depends on the material, contamination, and component geometry.
| Component type | Typical cleaning challenge | Important consideration |
|---|---|---|
| Aluminium valve blocks | Coolant and fine chips in internal passages | Material-compatible detergent and careful positioning |
| Stainless steel housings | Oil, grease and machining residue | Appropriate power and cleaning chemistry |
| Precision threaded parts | Residues between thread profiles | Suitable frequency and liquid penetration |
| Automotive metal components | Oil and particles in complex cavities | Effective cleaning, rinsing and drying |
Frequency selection should not be based on a simple rule that lower or higher frequencies are always better.
For example, 28 kHz and 40 kHz systems can produce different cavitation characteristics. The final selection should be based on the size of the contamination, the geometry of the component and the required surface condition.
For aluminium components, detergent compatibility is particularly important. Strongly alkaline cleaning solutions may affect the surface finish, so a cleaner specifically formulated for aluminium alloys should be considered.
5. Why Rinsing and Drying Are Just as Important
Removing contamination from a component is only part of the cleaning process.
After ultrasonic cleaning, loosened particles and detergent residues may remain in internal channels or blind holes.
Without proper rinsing, these residues may stay inside the component even if the initial ultrasonic cleaning stage was effective.
A suitable process may include:
Step 1: Ultrasonic cleaning
Remove machining oil, coolant and loose particles using a suitable cleaning solution.
Step 2: Rinsing
Use clean water to remove remaining detergent and suspended contamination. Components with internal passages may require additional rinsing or liquid movement.
Step 3: Drainage
Position the components to allow liquid to escape from blind holes and internal channels.
Step 4: Drying
Use an appropriate drying method to prevent moisture from remaining inside the component. Compressed air or hot-air drying may be suitable depending on the part design and material.
For high-precision applications, drying requirements should be verified rather than judged only by the external appearance of the component.
6. How Can Manufacturers Verify Internal Cleaning Results?
A visually clean surface does not necessarily mean that a component is completely clean.
For parts with internal channels, manufacturers should consider more targeted inspection methods.
Borescope inspection: Allows operators to examine internal passages that cannot be viewed directly.
Extraction testing: A selected sample can be flushed or rinsed, and the extracted particles can be collected for inspection.
Filter residue analysis: A suitable filter can capture particles from the extraction liquid for further examination.
Repeatability testing: Check multiple components from different production batches to evaluate whether the cleaning process delivers consistent results.
The inspection method should match the required cleanliness level and the function of the component.
7. Final Thoughts: Cleaning Complex Parts Requires More Than Ultrasonic Power
Ultrasonic cleaning is an effective solution for many CNC-machined metal components, but achieving good results in blind holes and internal channels requires attention to several factors.
Liquid penetration, component positioning, degassing, cleaning chemistry, rinsing and drying all contribute to the final result.
For manufacturers working with hydraulic components, aluminium housings and precision-machined parts, developing the right cleaning process is just as important as selecting the right equipment.
At BSTSONIC, we believe that understanding the component geometry and actual contamination is the starting point for choosing an appropriate ultrasonic cleaning solution.
The best cleaning result does not simply come from using more power. It comes from making sure the cleaning process reaches every area that needs to be cleaned.


